MSV MSAT G2 Spezifikationen

Power CableFigure 11 – Power Cable DetailsMSAT-G2 Installation Guide 80.25 A, 1-1/4 BY 1/4 FUSE10 + / - 0 . 5 INCHES20 FEET + / - 4 INCHES6 + /

Standard Cable ConnectionsIn addition to the DC power connection, optional horn alert and ignition sense connectionsmay be made. These are all done us

Basic Installation ProcedureWhile the installation of the MSAT-G2 mobile satellite radio is straightforward, it is essentialthat the installation be d

Lightning ArrestorsThe applicable electrical code(s) may require that lightning arrestors capable of supporting L-band transmissions be installed on a

Instructions for the installer:1. The mounting bracket should be used for mounting the TU.2. Mount the mounting bracket onto a flat surface using at l

MSAT-G2 Installation Guide 13HANDSETSERIAL PORTETHERNETSERIAL PORT ETHERNETHANDSET176.83533.6DIMENSIONS WITH MOUNTING BRACKETMSV TRANSCEIVER UNITFigur

The Antenna Unit (AU)The antenna unit is composed of the antenna element array, necessary high power and lownoise amplifier systems and a tracking sys

Do not locate the antenna close to interfering signal sources or receivers. It is recommendedthat no other antennas be located within three (3) meters

Magnetic Mount InstallationThe Magnet Mount consists of (3) three individual high intensity magnets with rubber coating. Each magnet has a stainless s

Permanent (Mast) MountingFor permanent mounting of the SPAC-AS-MSV220, a special Pole Mount Installation Kit isavailable. SpaceCom part no.: SPAC-AC-1

Introduction ... 1Transceiver Unit (TU) ...

Figure 19 – SPAC-AS-MSV220 2-axis Antenna W/ Optional Pole MountSPAC-AS-MSV320 Maritime AntennaWhen installing a SpaceCom Maritime Antenna on a vessel

2pcs. Clamp, Part No. SPAC-M004282pcs. Clamp, Part No. SPAC-M004298pcs. Nuts M8, Part No. SPAC-M90-101052pcs. Flange, Part No. SPAC-M00430 1pcs. Plug

Bushings, Part No. SPAC-M00227 are used to ensure NO electrical contact between themechanical parts of the antenna (in the dome) and the mounting pole

SPAC-AS-MSV320 Antenna InstallationInstallation of the 3-axis antenna on the mast is done according to FIG 21. The diameter of the post shall preferab

Figure 21 – SPAC-AS-MSV320 3-axis Antenna Installation DetailsMSAT-G2 Installation Guide 22Plug for mounting polePart No.: SPAC- MO0233 (1 0NLY)Coax

Installing the HandsetThe handset can be mounted using a standard-sized microphone clip mount (included).Select a mounting position for the handset. T

Error Code DiagnosticsThe following error messages may be displayed on the handset.MSAT-G2 Installation Guide 24Error ConditionFAILED TOCOMMISSION COM

Figure 22 – Error CodesMSAT-G2 Installation Guide 25INVALID DN NO TGBLOCKED X-OVER FAILURE RF POWERFAILUREANTENNAFAILUREWARNING!OVERHEATINVALIDPASSWOR

Troubleshooting the InstallationSteps to Basic TroubleshootingWhen troubleshooting, always record as much information as possible at all times. Start

5) Troubleshoot by componentDoes the problem sound TU-related, antenna-related, handset-related or externalequipment-related? Swap out a suspect compo

IntroductionThe purpose of this guide is to provide assistance to personnel installing the new MSAT-G2mobile satellite radio equipment. The guide star

MSAT-G2 Technical SpecificationsFigure 23 – Technical SpecificationsMSAT-G2 Installation Guide 28Weight HUGHES 2100 TU = 0.8 lbsDT-200 Handset = 0.6

MSAT-G2 Installation Guide 29Mobile Satellite Ventures Customer Service 1-800-216-6728 [email protected] Copyright © 2005 MSV All rights reserved. Thi

An optional external speaker may be connected to the TU for remote monitoring. Serial andethernet ports are provided for external interfacing, debuggi

Transceiver Unit (TU)The TU provides the interface for the handset and antenna unit (AU) and manages thecommunications over the MSV network. It also d

The TU is equipped with the following ports:Power PortThe power port is the connection from the power supply (vehicle battery or some other 12VDC powe

Serial PortThe serial port is a female DB-9F RS 232 and can be used for NMEA output (GPS) andcrossbanding.Figure 6 – Serial Port PinoutAntenna PortThe

Handset PortThe RJ45 handset port is used to connect the handset to the TU. The connector type is a modular 8 position and 8 conductor RJ45. The pinou

Figure 9 – Transceiver Unit Front & Back System Power Requirements There is only one power connection for the entire radio. This must be connected